Emtek Keypad Leverset Locksets (Adjustable Latch) Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Pro domov Emtek Keypad Leverset Locksets (Adjustable Latch). Emtek Keypad Leverset Locksets (Adjustable Latch) User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 12
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Installation & Programming Guide
Keypad Lever Locksets
ASSA ABLOY, the global leader in door opening solutions
Zobrazit stránku 0
1 2 3 4 5 6 ... 11 12

Shrnutí obsahu

Strany 1

Installation & Programming GuideKeypad Lever LocksetsASSA ABLOY, the global leader in door opening solutions

Strany 2 - What’s in the Box

10In order to perform each of the following six functions, the lock must rst be placed in Programming Mode:*If no input within 10 seconds, Yellow LED

Strany 3 - IMPORTANT!

11IN8-KEYPADLL1 02/26/2013Restoring the Lock to Factory Default Setting• Remove power (disconnect 9V battery) from Lock • Press and Hold EMTEK butto

Strany 4 - 1. Install Adjustable Latch

ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience.Copyright © 201

Strany 5 - (item #4c)

3692454b4a214c4d768ITEM NO. DESCRIPTION QTY.1 Key 22 Outside Trim Plate Assembly 13 Adjustable Latch for 2 ⁄” or 2 ¾” Backset 14 Inside Trim Plate A

Strany 6 - 4. Install Inside Chassis

2 ⁄” or 2 ¾” Backset2 ⁄” Dia Bore⁄” Deep2 ¼”1 “1” Diameter Edge Bore2. Door Prep 3. Door Jamb Prep1. Conrm HandingHANDING OF DOOR IS ALWAYS DE

Strany 7

4Screws (item #4c)Use a Phillips head screwdriver to remove screws (item #4c) shown below and detach Inside Trim Plate from the Inside Chassis.Fasten

Strany 8 - Screws (item #4c)

5Screws (item #4c)3. Install Outside Trim Plate AssemblyStep 1: While holding Outside Trim Plate Assembly, Press the Plastic Extender (A) into end of

Strany 9

64. Install Inside ChassisCAM LINK MUST REMAIN IN THE CORRECT POSITION DURING INSTALLATION.!Step 1: Conrm the position of Cam Link.For Left Hand Loc

Strany 10 - Programming Your Lock

7Step 4: Connect Wire Harness (A) and tuck Connectors as shown (B).ABStep 5: Install Battery.For optimal performance, always use a good quality bat

Strany 11 - IN8-KEYPADLL1 02/26/2013

8!USER CODES ARE LOCATED ON THE INSIDE TRIM PLATE & ON PAGE 11.Inside 5. Install Inside Trim PlateFasten Inside Trim Plate using two #8-32 x ⁄”

Strany 12

9Your Emtek lock is shipped with two 4-digit user codes and a 6-digit programming code. These codes are randomly generated at the factory. (Turn to ne

Komentáře k této Příručce

Žádné komentáře